Sourcing desk · South Jinqiao Area, Pudong, Shanghai sale@machinerychina.org +86 21 6044 5623

Knowledge base · Cranes & lifting

Nordberg Mine Hoist Parts

1,841 words About 8 min read Published by YJMT
Overhead crane
Answer Here is a list of most parts found on a Nordberg Mine Hoist:Brake Priming is used with automatic or semi-automatic control. when the hoist is approaching a stop, it slows down to a creep speed.

Here is a list of most parts found on a Nordberg Mine Hoist:Brake Priming is used with automatic or semi-automatic control. when the hoist is approaching a stop, it slows down to a creep speed. during this creeping, the clearance is removed between the brake shoes and the brake wheel. when the final stop signal is given, accurate spotting can be attained since the brakes are already partially applied.

Coefficient of Friction has particular importance when referring to Friction Hoists since it refers to the driving friction developed between the hoist rope or ropes and the friction tread material mounted on the hoist. since the hard wires of the rope actually imbed themselves in the softer friction material, it is sometimes referred to as the “Coefficient of Grip”. many types of materials have been used for the friction treads – wood, leather, rubber and plastic. the allowable coefficients of friction and bearing pressure will vary with the type of friction material and size of rope and wheel used.
Controls: Automatic – Usually on a production hoist. with this type of control, a skip is spotted at the loading pocket and the cycle is initiated by a pushbutton. the hoist will then load, run and upload continuously until a stop signal is given.
Semi-Automatic – Similar to automatic control, except that the hoist stops at the end of each cycle and is then started again by pushbutton.
Manual – Requires a hoist operator at all times. he manually regulates the amount of electric power and the necessary mechanical braking. Manual control, of course, requires less equipment. Automatic and semi-automatic hoists also have provisions for manual control.
Creep (Rope) applies to Friction Hoists and describes the action of the rope or ropes actually creeping over the drum in the direction of rotation. this is caused by the ropes being stretched by the load on the high tension side and passing over the drum to a lower tension condition. this action is not to be confused with slip.
Drum Hoist is any hoist that has one end of the rope or ropes anchored to the drum and uses the drum for rope storage.
Friction Koepe Hoist is any hoist that uses the principle of friction to drive the rope.
Koepe wheel – since the size of the drum on the Koepe hoist is considerably smaller either in width or diameter than the drum on a comparable drum hoist, it is sometimes referred to as a wheel.
Fleet Angle is the angle the ropes makes with the drum as it deviates from perpendicular when winding across the drum. this angle should never exceed 1½°. for multilayer winding the minimum is 0°30’.
Rope pull is a term very often used with two different meanings. Sometimes rope pull is defined as the load attached to the end of the rope, and sometimes as the rope pull at the drum (which includes the load attached to the rope as well as the weight of the rope itself). when using the term rope pull, the loads included should be specified.
Slip (Rope) occurs when the coefficient of friction or grip is not sufficient to supply the necessary driving or braking force on a friction hoist.
Slope Hoist is a particular type of drum hoist usually associated with an unbalanced rope pull on an incline.
Synchronizer – every Koepe Hoist requires a synchronizer. since the rope or ropes are not fastened directly to the drum, it is possible to have relative movement between the drum and rope, such as creep or slip, which puts the indicating devices out of adjustment. with the hoist at rest the synchronizer may be adjusted manually or automatically to correct the indicating and safety devices.
Tension Ratio T1 / T2 is the ratio of the heavier side rope tension (T1) to the lighter side rope tension (T2). this is a consideration only with friction hoists.

Sourcing desk

Need the machine, not just the theory?

Send the specification and destination port. You get a factory-direct price, lead time and shipping estimate within two business days.